I suspect we may see a lot of countries get pushy about trying to encourage people to have kids. There were lots of short term economic benefits to pushing families into having both partners working, but in the long term countries are still built around needing a growing population to do well.

You can offset lower birthrates with immigration to an extent, but itherwise we would need pretty major social changes to sustain society if birth rates continue to decline.

Alternative wording is gives you an erection for the rest of your life.

No, I straight up had two different installation media’s fail until I went back and shut down windows fully. I’ve never run into that before on an install before.

First I tried ZorinOS, and it would fail to even boot into the live environment. I tried multiple times and even made a new install media. Then I tried fedora silverblue, it would get into the install environment but couldn’t do any kind of partitioning etc to the drive. I then rebooted to windows, shut it down fully, and tried again. This time fedora could edit the drive partitions, and zorin could load the live environment and install.

Previously I’ve had issues with shared drives being locked by windows, but this was the first time I’ve ever had an install fail because windows wasn’t shutdown fully. I don’t usually dual boot these days either though (I was setting up this computer for family) so I figured maybe something had changed with newer versions of windows or device security.

Make sure windows was shut down all the way. Normally when you shutdown windows, it only hibernates and it locks it’s partitions to prevent editing. I tried installing Zorin for a family member recently, and it couldn’t install until I booted back into windows and shut it down fully.

To shutdown fully, in windows you need to either hold shift while clicking the shutdown button, or open the run box and run the command shutdown -s -t 00

New drugs get a period of time where the company that developed it has exclusive manufacturing rights. The idea is that if anyone can start making the drug immediately, there’s not a good reason for companies to spend money to develop new drugs. However if demand for a drug is greater than the ability of the creating company to produce the drug, other companies are allowed to temporarily step in and make up the difference.

No, because apple’s monopoly doesnt count because they’re upfront about it being a monopoly.

Which is stupid, but that’s how it works apparently

It’s not like the current group of users is perfect either. There’s a lot of circlejerk opinions going around, and I’ve seen being get majorly downvoted for posting factual info that went against the “hivemind” opinion.

Yeah, it’s unfortunately common to have games running better through proton than the native port. We’ve seen a lot of devs drop their linux port recently because the proton version ran better with fewer issues.

Obviously a well executed native linux port is preferable, but a lot of smaller devs have trouble justifying spending a lot of time working out kinks for a linux port if the game already runs great through proton.

Windows is absolutely abusing their position as the dominant OS to push their other products. The number of “no don’t do that” messages and pop ups when trying to install chrome on a windows computer is clearly anti-competitive, and the only reason microsoft has been getting away with it is because Edge/etc hasn’t achieved enough market share.

Right, but in my case I’m not actually a customer of the local electric company that offers fiber. However pressure from them got my telco company (the only choice I have besides satellite) to offer me fiber, raising my max speed from 3Mb/s to 1000Mb/s.

Do you live off grid?

Definitely seeing that where I live. One of the local electric companies started offering gigabit fiber for $75, where most people were paying a lot more than that for DSL or low quality satellite (which were the only choices before). It’s been a huge improvement for those people, and it’s forced some of the long stagnant Telco companies to actually compete and start rolling out fiber of their own.

Recently ran into an issue with Endeavour OS where the built in printer program would give errors when trying to add my network ecotank printer.

Tried using cups terminal and it worked the first time, and is still working weeks later.

So some of the GUI printer apps that distros ship with have issues apparently, but I don’t know the extent of it.

There’s a big difference between doom scrolling and education.

They added wifi with a extra circuit board hidden inside the calculator case. It’s connected to the calculators communication port, and pretends to be another calculator. So they can use the calculator’s built in “send” function to send variables/text/etc to the hidden card, which then uses it’s internet connection to look up answers and send the results back.

This definitely feels like terrorist attack tactics, since it does more to cause fear than actually fatalities. You make some really good points though, it’s unfortunate that you’re getting so many downvotes for factual information.

As for the terrorist group designation, you can see a list of all countries and entities that consider Hezbollah a terrorist group here.. It does include both the European Union and the United States, along with many other countries. There are some countries that don’t consider them a terrorist group, notably Russia, China, and North Korea.

Huh, possibly bad extruder? If it’s got weak extrusion it might only be able to push it through the nozzle at higher temps.

That was a good investigation and explanation about a weird number of up votes. Thanks for explaining it.

It really sounds like you have a major problem with the printer that needs to be resolved. Without knowing any more details I would suggest making sure the nozzle isn’t clogged and possibly replacing the hot end.

I had similar printing issues with some filaments, due to heat creep. The printing would start ok on mine, but after the printer had been running awhile it would print like that. In my case heat was travelling up the hot end and Bowden tube, which was causing printing issues after a certain amount of time had passed. Some filaments were more sensitive about this than others, my cheap plain filaments and my multicolor filaments wouldn’t print well, but medium to high quality plain filaments would print fine.

There are a lot of things that can contribute to heat creep, I ended up replacing my hot end and Bowden tube, and lowered my print temperature some.

220° is pretty high, I would try to figure out why it won’t print below that temperature and see what you can do to bring that down. See if that fixes it.